mm
Table of Contents
MM
TeleType Communications
MM sets the Brewer program to its teletype (terminal) mode, whereby the operator may communicate directly with the Brewer via the computer keyboard and a set of low level commands.
Exit from teletype mode by typing EXIT.
See Appendix H for more explanation on the TeleType feature.
List of commands
| Command | Variables | Usage | Description |
|---|---|---|---|
| A | Repeats the command. Usually use in conjunction with another command move. (I.E. R,0,7,5:O:A) Press home to delete twice to go exit. | ||
| B,x | |||
| B,2 | This command controls the lamps | ||
| M,m,s | |||
| M,10,500 | Moves motor m to step s. Note: when moving backwards (negative number) it will set that as the new reference point. Click here more motor information. | ||
| O | O | ||
| R,p1,p2,t | |||
| R,0,5,7 | This command is used to measure the light intensity according to the variables setup. Often this command is combined with the O command to output the results. R,0,5,7:O | ||
| SL | SL | ||
| SL+ | SL | ||
| HG+ | HG+ | ||
| FWFilter wheel number,Position | Filter wheel number Filter wheel 1 or 2 Position - What position to move to | FW1,2 | Move the selected filter wheel to the selected position |
| TStart Location2End Location | |||
| TOP2MAX | This command will move the micrometer 1 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range. | ||
| BStart Location2End Location | |||
| BOP2MAX | This command will move the micrometer 2 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range. | ||
| exit | exit | exit's mm and return to menu ('quit' will do the same thing) |
For multiboard electronics only
| Command | Variables | Usage | Description |
|---|---|---|---|
| E,m | |||
| E,9 | This command zeros the motor and return the number it takes to get to the LED. NOTE: This will not return the motor and will leave it at the LED | ||
| x,s1,s2 | s1 and s2 refers to the number of steps to move for micrometer 1 and 2 respectively. | x,100,200 | Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. Click here more motor information. |
For new electronics only
| Command | Variables | Usage | Description |
|---|---|---|---|
| ?<command> OR !<command> | See Operation Information | A variety of operational commands/status output for the brewer. for more. | |
| I,m | |||
| I,9 | This commands re-initializes the specified motor | ||
| N,s | s refers to the number of steps | N,500 | (Used for singleboard electronics only.) Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. Click here more motor information. |
| SAVE | SAVE | Stores the current set of RAM configuration parameters | |
| ?MZ10 | ?MZ10 | Runs the command ?MOTOR.ZERO.POS[10] | |
| ?MZ9 | ?MZ9 | Runs the command ?MOTOR.ZERO.POS[9] | |
| ?MP10 | ?MP10 | Runs the command ?MOTOR.POS[10] | |
| ?MP9 | ?MP9 | Runs the command ?MOTOR.POS[9] | |
| ?MD10 | ?MD10 | Runs the command ?MOTOR.DISCREPANCY[10] | |
| ?MD9 | ?MD9 | Runs the command ?MOTOR.DISCREPANCY[10] |
mm.txt · Last modified: by reno