Differences

This shows you the differences between two versions of the page.

--- singleboard [2025/03/10 10:24] – [Lamp/Temp Board] -troubleshooting reno
+++ singleboard [2026/07/14 15:11] (current) – added heater information reno
@@ Line 21: / Line 21: @@
 {{ :docs:kz_splitboard_pcb_layout_b.pdf |}}
+===== Heater Controller =====
+The heater is controlled by a separate board that is normally attached to the back of the foreoptics support in front of the stock location of the heater. The minium temperature can be controlled via J1
+^Jumper setting^Minimum temperature^
+|1-2|20°C|
+|2-3|10°C|
 ===== Mainboard Flat Cable Connections =====
@@ Line 49: / Line 53: @@
 {{:misc:20201019_074344_resized.jpg?300|}}
 |SL Voltage|HG Voltage|SL Current|
+===== Brewer Base Plate =====
+<hidden Single Board Brewer Base Plate Drawing>{{:brewer_main:single_board_base_detail-1.jpg?400|}}
+{{:brewer_main:single_board_base_holes-1.jpg?400|}}
+{{:brewer_main:single_board_bm-c215_rev_1_spectrometer_weatherproof_base-1.jpg?400|}}</hidden>
+\\
 ==== Troubleshooting ====
+=== AP Lamps Results ===
 Possible issues with via AP results
-^:::^Working Order^^Disconnected DB connector @ Lamp^^No power to Lamp Board^^Missing 24V @ Lamp Board^^
+^:::^Working Order^^Disconnected DB connector @ Lamp^^No power to Lamp Board^^Missing 24V @ Lamp Board^^Bad Connection on Power connector¹^^
-^Name^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^
+^Name^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^
-|Std Lamp current(A)|0.00|1.51|0.01|0.00|0.02|0.01|0.01|0.00|
+|Std Lamp current(A)|0.00|1.51|0.01|0.00|0.02|0.01|0.01|0.00|2.48|2.48|
-|Std Lamp Voltage(v)|0.03|10.44|6.84|12.83|5.29|3.16|0.04|0.03|
+|Std Lamp Voltage(v)|0.03|10.44|6.84|12.83|5.29|3.16|0.04|0.03|14.09|14.06|
-|Mer Lamp current(A)|0.00|0.46|0.01|0.23|0.00|0.00|0.00|0.00|
+|Mer Lamp current(A)|0.00|0.46|0.01|0.23|0.00|0.00|0.00|0.00|0.00|0.00|
-|Mer Lamp Voltage(v)|0.54|12.86|0.56|12.88|5.48|3.25|0.03|0.01|
+|Mer Lamp Voltage(v)|0.54|12.86|0.56|12.88|5.48|3.25|0.03|0.01|14.81|14.11|
+¹More testing required.
+=== Status LED ===
+^LED Mode Indication^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^
+^Cosmac Mode normal operation|**on**|off|off|off|**on**|**on**|**on**|off|
+^Cosmac Mode with config missing|**on**|off|off|off|**on**|off|**on**|off|
+^Loadmode Waiting for firmware|**on**|off|**on**|off|**on**|off|**on**|off|
+^Loadmode with bad flash memory|**on**|**on**|**on**|**on**|**on**|**on**|**on**|off|
+^Loadmode with Good flash memory|**on**|**on**|**on**|**on**|**on**|**on**|**on**|off|
+^Opmode with config|**on**|**on**|off|off|**on**|**on**|off|off|
+^Opmode without config|**on**|**on**|off|off|**on**|off|**on**|off|
+^Checking flash memory|**on**|off|**on**|off|off|off|off|off|
+^Changing modes|**on**|**on**|**on**|**on**|**on**|**on**|**on**|**on**|
 ===== Commands =====
 Frequency used commands in MM