Canadian Brewer Spectrometer Network

User Tools

Site Tools

Trace:
mm

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
mm [2025/08/11 18:23] – renomm [2025/08/12 13:54] (current) – reno
Line 30: Line 30:
   s refer to the number of steps to move   s refer to the number of steps to move
 |M,10,500|Moves motor m to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].| |M,10,500|Moves motor m to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
-|N,s|s refers to the number of steps|N,500|(Used for [[singleboard|singleboard electronics]] only.) Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].| 
 |O| |O|This command outputs the number of counts returned in a measurement. |O| |O|This command outputs the number of counts returned in a measurement.
 |R,p1,p2,t|\\ |R,p1,p2,t|\\
Line 75: Line 74:
 |BOP2MAX|This command will move the micrometer 2 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.| |BOP2MAX|This command will move the micrometer 2 to max/op/min position to max/op/min. It assumes the micrometer is already in the start location. This is use to help test the micrometer range.|
 |exit|  |exit|exit's mm and return to menu ('quit' will do the same thing)| |exit|  |exit|exit's mm and return to menu ('quit' will do the same thing)|
-  +\\   
 +==== For multiboard electronics only ==== 
 +^Command^Variables^Usage^Description^ 
 +|E,m| \\ 
 +  m refers to a motor number 
 +  1. Zenith prism 
 +  2. Azimuth Tracker 
 +  3. Iris 
 +  4. Filterwheel 1 
 +  5. Filterwheel 2 
 +  6. Filterwheel 3 or Micrometer 2 (bottom) 
 +  10. Micrometer 1 (Top) 
 +  11. Slitmask 1 
 +  12. Slitmask 2 
 +  13. Zenith tracker 
 +|E,9|This command zeros the motor and return the number it takes to get to the LED. NOTE: This will not return the motor and will leave it at the LED| 
 +|x,s1,s2|s1 and s2 refers to the number of steps to move for micrometer 1 and 2 respectively.|x,100,200|Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].| 
  
 ==== For new electronics only ==== ==== For new electronics only ====
Line 95: Line 111:
 | |
 |I,9|This commands re-initializes the specified motor| |I,9|This commands re-initializes the specified motor|
 +|N,s|s refers to the number of steps|N,500|(Used for [[singleboard|singleboard electronics]] only.) Moves both micrometer 1 and 2 to step s. Note: when moving backwards (negative number) it will set that as the new reference point. [[motor|Click here more motor information]].|
 |SAVE|   |SAVE|Stores the current set of RAM configuration parameters| |SAVE|   |SAVE|Stores the current set of RAM configuration parameters|
 |?MZ10|   |?MZ10|Runs the command <key>?MOTOR.ZERO.POS[10]</key>| |?MZ10|   |?MZ10|Runs the command <key>?MOTOR.ZERO.POS[10]</key>|
mm.1754936605.txt.gz · Last modified: 2025/08/11 18:23 by reno