icf
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| icf [2026/07/28 19:57] – andrew | icf [2026/08/12 10:40] (current) – reno | ||
|---|---|---|---|
| Line 14: | Line 14: | ||
| |Dead time (sec)| Dead time the instrument is set to| | |Dead time (sec)| Dead time the instrument is set to| | ||
| |WL cal step number| Current cal step for the instrument | | |WL cal step number| Current cal step for the instrument | | ||
| - | |Unused| | | + | |Slitmask Motor Delay|Multi-board electronics - This is the slitmask delay between moving from one slit to the next. The typical value for this is 80\\ New Electronics - This sets the speed of the slitmask motor, typically and usually left at 14.| |
| |Umkehr Offset| Azimuth offset during Umkehr measurements | | |Umkehr Offset| Azimuth offset during Umkehr measurements | | ||
| |ND filter 0| Filer correction from Neutral Density (ND) filter #0 | | |ND filter 0| Filer correction from Neutral Density (ND) filter #0 | | ||
| Line 24: | Line 24: | ||
| |Zenith steps/rev| The number of steps to perform a complete rotation of the zenith | | |Zenith steps/rev| The number of steps to perform a complete rotation of the zenith | | ||
| |Brewer Type| Version of Brewer spectrophotometer | | |Brewer Type| Version of Brewer spectrophotometer | | ||
| - | |COM Port #| | | + | |COM Port #| Select the comport being used. **if using dosbox or similar dos emulator, this is not the actual comport used on the computer, but the comport specified in the config. Typically left as 1| |
| |o3 Temp coef hg| | | |o3 Temp coef hg| | | ||
| |n2 Temp coef hg| | | |n2 Temp coef hg| | | ||
| Line 42: | Line 42: | ||
| |NO2/O3 Mode Change| | | |NO2/O3 Mode Change| | | ||
| |Grating Slope| The relationship of movement between micrometer #1 and micrometer #2 to maximize counts| | |Grating Slope| The relationship of movement between micrometer #1 and micrometer #2 to maximize counts| | ||
| - | |Grating Intercept| | | + | |Grating Intercept|:::| |
| |Micrometer Zero| | | |Micrometer Zero| | | ||
| |Iris Open Steps| The number of steps it takes to open the Iris | | |Iris Open Steps| The number of steps it takes to open the Iris | | ||
| Line 54: | Line 54: | ||
| |Release date| Date that the ICF was created| | |Release date| Date that the ICF was created| | ||
| |EXTRAS| | | |EXTRAS| | | ||
| - | |AUTO HG| | | + | |AUTO HG|Allows the software to automatically insert HG as required when running a schedule with auto routine. Typically an HG is ran every 2 hours or a change in temperature of 2 degrees, which ever happens first. \\ 0 - Disable \\ 1 - Enable| |
| - | |FW2 oscil| | | + | |FW2 oscil|Allows filterwheel 2 to keep changing with no limits during DS measurements. This usually happens when the sun gets covered/ |
| |HG FW#2 Pos| Position of filter wheel #2 when using the Hg bulb | | |HG FW#2 Pos| Position of filter wheel #2 when using the Hg bulb | | ||
| |Low Signal limit| The number of counts at which the instrument will switch to a lower neutral density filter or skip the test during a direct sun measurement| | |Low Signal limit| The number of counts at which the instrument will switch to a lower neutral density filter or skip the test during a direct sun measurement| | ||
| |Upper Signal limit| The number of counts at which the instrument will increase the neutral density filter during a direct sun measurement| | |Upper Signal limit| The number of counts at which the instrument will increase the neutral density filter during a direct sun measurement| | ||
| - | |Use cubic DSP| | | + | |Use cubic DSP|Enable the use of cubic dispersion. \\ 0 - Disable \\ 1 - Enable| |
| |Skip DS if too dim| Enable skipping a Direct Sun (DS) measurement if counts are too low | | |Skip DS if too dim| Enable skipping a Direct Sun (DS) measurement if counts are too low | | ||
| |O3ETC-R6| Ozone Extraterrestrial Constant (ETC) minus the R6 standard lamp ratio | | |O3ETC-R6| Ozone Extraterrestrial Constant (ETC) minus the R6 standard lamp ratio | | ||
icf.1785268620.txt.gz · Last modified: 2026/07/28 19:57 by andrew