Canadian Brewer Spectrometer Network

User Tools

Site Tools

Trace:
singleboard

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
singleboard [2025/02/06 15:50] – renosingleboard [2025/12/04 17:00] (current) – reno
Line 7: Line 7:
 <hidden Single Board Top>{{ :boards:singleboard_v1_top.jpg?600 |Single Board Top V1}}</hidden> <hidden Single Board Top>{{ :boards:singleboard_v1_top.jpg?600 |Single Board Top V1}}</hidden>
 <hidden Single Board Bottom>{{ :boards:singleboard_v1_bottom.jpg?600 |Single Board Bottom V1}}</hidden> <hidden Single Board Bottom>{{ :boards:singleboard_v1_bottom.jpg?600 |Single Board Bottom V1}}</hidden>
 +<hidden Voltage Test Point>
 +^Connect J23^   Pin   ^^^^^^^^^^
 +^:::^1^2^3^4^5^6^7^8^9^10^
 +|   |5v|5v|-5v|12v|12v|-12v|24|2.5v|4.5v|GND|
 +</hidden>
 {{ :docs:brewer_mkiii_operators_manual_revd.pdf |Operator Manual}}\\ {{ :docs:brewer_mkiii_operators_manual_revd.pdf |Operator Manual}}\\
 {{ :docs:mkiii_service_manual_revd_sb.pdf |Service Manual}} {{ :docs:mkiii_service_manual_revd_sb.pdf |Service Manual}}
Line 19: Line 24:
  
 ===== Mainboard Flat Cable Connections ===== ===== Mainboard Flat Cable Connections =====
-^Cable^Name^Useage^Default Address^ +^Cable^Name^Useage^Default Address^Jumper settings^ 
-|J2 Top|BA-W77/A|Lamp Board|  | +|J2 Top|BA-W77/A|Lamp Board|  |   | 
-|J2 Bottom|BA-W77/B|J1 on hv module|  | +|J2 Bottom|BA-W77/B|J1 on hv module|  |   | 
-|J13 Top|BA-W76/B|Iris|Motor 3| +|J13 Top|BA-W76/B|Iris|Motor 3|**[E35 E37]** (E38 E38)| 
-|J13 Bottom|BA-W76/A|Zenith|Motor 1| +|J13 Bottom|BA-W76/A|Zenith|Motor 1|**[E39 E40]** (E41 E42)| 
-|J14 Top|BA-W76/B|Filter wheel #1|Motor 4| +|J14 Top|BA-W76/B|Filter wheel #1|Motor 4|**[E71 E72]** (E73 E74)| 
-|J14 Bottom|BA-W76/B|Filter wheel #2|Motor 5| +|J14 Bottom|BA-W76/B|Filter wheel #2|Motor 5|**[E75 E76]** (E77 E78)| 
-|J15 Top|BA-W76/A|Micrometer #2 (MKIII only)|Motor 9| +|J15 Top|BA-W76/A|Micrometer #2 (MKIII only)|Motor 9|[E107 E108] **(E109 E110)**| 
-|J15 Bottom|BA-W76/A|Micrometer #1|Motor 10| +|J15 Bottom|BA-W76/A|Micrometer #1|Motor 10|[E111 E112] **(E113 E114)**| 
-|J16 Top|  |Spare|Motor 7| +|J16 Top|  |Spare|Motor 7|[E143 E144] (E145 E141)| 
-|J16 Bottom|BA-W76/C|Filter wheel#3 (MK IV only}|Motor 6| +|J16 Bottom|BA-W76/C|Filter wheel#3 (MK IV only}|Motor 6|**[E147 E148]** (E149 E150)| 
-|J17 Top|BA-W76/B|Slitmask (shutter)|Motor 11| +|J17 Top|BA-W76/B|Slitmask (shutter)|Motor 11|**[E179 E182]** (E181 E182)| 
-|J17 Bottom|BA-W76/A|Azimuth|Motor 2| +|J17 Bottom|BA-W76/A|Azimuth|Motor 2|   | 
-|J12 Top|BA-W76/A|Control switch’s|  | +|J12 Top|BA-W76/A|Control switch’s|  |   | 
-|J12 Bottom|  |  |  | +|J12 Bottom|  |  |  |   | 
-|J20 Top|   |Spare|Motor 12|+|J20 Top|   |Spare|Motor 12|[E7 E8] (E9 E10)
 |J20 Bottom|  |Spare - New AZ motor|Motor 8| |J20 Bottom|  |Spare - New AZ motor|Motor 8|
 |J7 Top| |Communication|  | |J7 Top| |Communication|  |
 |J7 Bottom| |Humidity sensor|  | |J7 Bottom| |Humidity sensor|  |
 Note 1: Top Refers to the connector on the stop of the ribbon connector stack on a V1 board when looking at it on a birds eye view. For V2 boards, it is the connector closer to the bottom of the board.\\ Note 1: Top Refers to the connector on the stop of the ribbon connector stack on a V1 board when looking at it on a birds eye view. For V2 boards, it is the connector closer to the bottom of the board.\\
-Note 2: From the table above, J2 is the connector on the top right of the board, and going left. J7 is on the bottom right of the board.+Note 2: From the table above, J2 is the connector on the top right of the board, and going left. J7 is on the bottom right of the board.\\ 
 +Note 3: [] indicates 12V pair and () indicates 24V pair and **bold** indicates jumper default
 ===== Lamp/Temp Board===== ===== Lamp/Temp Board=====
 {{:misc:20201019_074344_resized.jpg?300|}} {{:misc:20201019_074344_resized.jpg?300|}}
 |SL Voltage|HG Voltage|SL Current| |SL Voltage|HG Voltage|SL Current|
  
 +===== Brewer Base Plate =====
 +<hidden Single Board Brewer Base Plate Drawing>{{:brewer_main:single_board_base_detail-1.jpg?400|}}
 +{{:brewer_main:single_board_base_holes-1.jpg?400|}}
 +{{:brewer_main:single_board_bm-c215_rev_1_spectrometer_weatherproof_base-1.jpg?400|}}</hidden>
 +\\
 +==== Troubleshooting ====
 +=== AP Lamps Results ===
 +Possible issues with via AP results
 +^:::^Working Order^^Disconnected DB connector @ Lamp^^No power to Lamp Board^^Missing 24V @ Lamp Board^^Bad Connection on Power connector¹^^
 +^Name^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^Value Off^Value On^
 +|Std Lamp current(A)|0.00|1.51|0.01|0.00|0.02|0.01|0.01|0.00|2.48|2.48|
 +|Std Lamp Voltage(v)|0.03|10.44|6.84|12.83|5.29|3.16|0.04|0.03|14.09|14.06|
 +|Mer Lamp current(A)|0.00|0.46|0.01|0.23|0.00|0.00|0.00|0.00|0.00|0.00|
 +|Mer Lamp Voltage(v)|0.54|12.86|0.56|12.88|5.48|3.25|0.03|0.01|14.81|14.11|
 +
 +¹More testing required.
 +=== Status LED ===
 +
 +^LED Mode Indication^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^¼Sec^
 +^Cosmac Mode normal operation|**on**|off|off|off|**on**|**on**|**on**|off|
 +^Cosmac Mode with config missing|**on**|off|off|off|**on**|off|**on**|off|
 +^Loadmode Waiting for firmware|**on**|off|**on**|off|**on**|off|**on**|off|
 +^Loadmode with bad flash memory|**on**|**on**|**on**|**on**|**on**|**on**|**on**|off|
 +^Loadmode with Good flash memory|**on**|**on**|**on**|**on**|**on**|**on**|**on**|off|
 +^Opmode with config|**on**|**on**|off|off|**on**|**on**|off|off|
 +^Opmode without config|**on**|**on**|off|off|**on**|off|**on**|off|
 +^Checking flash memory|**on**|off|**on**|off|off|off|off|off|
 +^Changing modes|**on**|**on**|**on**|**on**|**on**|**on**|**on**|**on**|
 ===== Commands ===== ===== Commands =====
 Frequency used commands in MM Frequency used commands in MM
Line 51: Line 85:
 |?motor.ref.low[<key>x</key>]|checks the reference flag of motor <key>x</key> on the low side| |?motor.ref.low[<key>x</key>]|checks the reference flag of motor <key>x</key> on the low side|
 |?motor.address.[<key>MOTOR</key>]|checks the motor address used for <key>MOTOR</key>| |?motor.address.[<key>MOTOR</key>]|checks the motor address used for <key>MOTOR</key>|
 +==== Changing Motor Address ====
 +The motor address can be changed in event of a bad motor driver or circuitry. This will require the ribbon cable to be physically moved to another connector as laid out [[singleboard#mainboard_flat_cable_connections|here]]. Afterwards, enter [[mm|MM]] or opmode in brewcmd.
 +<konsole mm>
 +?motor.address[motorname]
 +#This will output the current motor address number, verify this is the one you want to change\\
 +!motor.address[motorname] 7
 +#replace 7 with the actual address you'd like to change to\\
 +i,10
 +#replace the 10 with the original address, this will reinitialize the motor\\
 +save
 +#once you verify everything is working as expected, you can save which will use up on of the save slots.
 +#otherwise when the brewer restarts, it'll be using the original motor address.
 +</konsole>
 +Note: anything starting with # are meant to be comments and not actual commands
 +
 +==== Motor names ====
 +  * AZIMUTH
 +  * IRIS
 +  * FILTER.WHEEL.1
 +  * FILTER.WHEEL.2
 +  * FILTER.WHEEL.3
 +  * MICROMETER.2
 +  * MICROMETER.1
 +  * SLITMASK.1
 +  * SLITMASK.2
 +  * TRACKER.ZENITH
 +  * ZENITH
  
singleboard.1738857012.txt.gz · Last modified: 2025/02/06 15:50 by reno