Canadian Brewer Spectrometer Network

User Tools

Site Tools

Trace: • multiboard
multiboard

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
multiboard [2025/04/03 17:10] – added wiring harness renomultiboard [2025/11/27 11:59] (current) – [FAQ] reno
Line 17: Line 17:
 For Diagnostics purposes, the minimal amount of boards required to communicate to the brewer from a computer is just the Microprocessor/RCA board and the [[photon_counter|Photon Counter Board]]. All the other boards can be removed. This will help diagnose if there is a bad board causing communication issues.\\ For Diagnostics purposes, the minimal amount of boards required to communicate to the brewer from a computer is just the Microprocessor/RCA board and the [[photon_counter|Photon Counter Board]]. All the other boards can be removed. This will help diagnose if there is a bad board causing communication issues.\\
 \\ \\
 +<hidden Cardcage Motherboard Signals>
 +^Component side^^^^Solder Side^^^^
 +^Pin^Mnemonic^Signal Flow^Discription^Pin^Mnemonic^Signal Flow^Discription^
 +^A|TPA-P|Out|System Timing Pulse 1^1|DMAI-N|In|DMA Input Request|
 +^B|TPD-P|Out|System Timing Pulse 2^2|DMAO-N|In|DMA Output Request|
 +^C|DB0-P|In/Out|Data Bus^3|RNU-P|---|Run Utility|
 +^D|DB1-P|In/Out|Data Bus^4|INT-P|In|Interrupt Request|
 +^E|DB2-P|In/Out|Data Bus^5|MRD-N|Out|Memory Read|
 +^F|DB3-P|In/Out|Data Bus^6|Q-P|Out|Programmed Output Latch|
 +^H|DB4-P|In/Out|Data Bus^7|SCO0-P|Out|State Code|
 +^J|DB5-P|In/Out|Data Bus^8|SCO1-P|Out|State Code|
 +^K|DB6-P|In/Out|Data Bus^9|CLEAR-N|In|Clear-Mode Control|
 +^L|DB7-P|In/Out|Data Bus^10|WAIT-N|In|Wait-Mode Control|
 +^M|A0-P|Out|Multiplexed Address Bus^11|-5V/-15V|---|Auxiliary Power|
 +^N|A1-P|Out|Multiplexed Address Bus^12|+24V|---|Auxiliary Power|
 +^P|A2-P|Out|Multiplexed Address Bus^13|Clock Out|Out|Clock from CPU Osc.|
 +^R|A3-P|Out|Multiplexed Address Bus^14|N0-P|Out|I/O Primary Address|
 +^S|A4-P|Out|Multiplexed Address Bus^15|N1-P|Out|I/O Primary Address|
 +^T|A5-P|Out|Multiplexed Address Bus^16|N2-P|Out|I/O Primary Address|
 +^U|A6-P|Out|Multiplexed Address Bus^17|EF1-N|In|External Flag|
 +^V|A7-P|Out|Multiplexed Address Bus^18|EF2-N|In|External Flag|
 +^W|MWR-N|Out|Memory Write Pulse^19|EF3-N|In|External Flag|
 +^X|EF4-N|In|External Flag^20|+12V/+15V|---|Auxiliary Power|
 +^Y|+5V|In|+5VDc^21|+5V|In|+5 volts dc|
 +^Z|GND|In|Digital Ground^22|GND|In|Digital Ground|
 +</hidden>
 ====== Wiring Harness ====== ====== Wiring Harness ======
 Note: These wiring harness are based on [[cbsn|CBSN]] brewer setup. Your brewer wiring may vary slightly Note: These wiring harness are based on [[cbsn|CBSN]] brewer setup. Your brewer wiring may vary slightly
-<hidden Secondary Power Supply - BA-W36 - P104 -TOP>+<hidden ==== Secondary Power Supply - BA-W36 - P104 -TOP ====>
 ^Connector Number^Connector Part Number^ ^Connector Number^Connector Part Number^
-|P104|EDAC 332-044-500-258|+|**P104**|EDAC 332-044-500-258|
 |TB1|Cinch 20-141| |TB1|Cinch 20-141|
 |P105|Cannon DBMA-25S| |P105|Cannon DBMA-25S|
Line 64: Line 90:
  
 </hidden> </hidden>
 +<hidden ==== Secondary Power Supply - BA-W36 - P104 -Bottom ====
 +>
 +^Connector Number^Connector Part Number^
 +|**P104**|EDAC 332-044-500-258|
 +|TB1|Cinch 20-141|
 +|P105|Cannon DBMA-25S|
 +|P111|Cannon DEMA9S|
 +|P113|Cannon DEMA9S|
  
 +^Internal Destination^^Origination^^^^^External Destination^^
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^
 +|1|Shutter +24V / RCL|A|TFE|22|Blue|80|2|P105|
 +|2|Shutter 0V (GND 3)|B|TFE|22|Black|60|18|TB1|
 +|3|Shutter RCL / Q303E|C|TFE|22|Green|80|3|P105|
 +|4|Shutter RCL / Q303B|D|TFE|22|Green|80|14|P105|
 +|5| |E|   No Connection   ||||||
 +|6|Shutter Motor / Q303C|F|TFE|22|Green|80|15|P105|
 +|7|Std Lamp   +15V/RCL|H|TFE|22|Red|80|6|P105|
 +|8|Std Lamp  0V  (GND 1)|J|TFE|22|Black|55|17|TB1|
 +|9|Std Lamp  Q103E/RCL|K|TFE|22|Violet|80|7|P105|
 +|10|Std Lamp  Q103B|L|TFE|22|Violet|79|20|P105|
 +|11|Std Lamp  Q103B|M|TFE|22|Violet|79|20|P105|
 +|12|Thermistor 2|N|TFE|24|Red|40|4|P113|
 +|13|Thermistor 2|P|TFE|24|Green|40|5|P113|
 +|14|Thermistor 2|R|TFE|24|Brown|40|6|P113|
 +|15|Thermistor 3|S|TFE|24|Red|40|7|P113|
 +|16|Thermistor 3|T|TFE|24|Green|40|8|P113|
 +|17|(GND 6)|T|TFE|22|Black|55|16|TB1|
 +|18|Thermistor 3|U|TFE|24|Brown|40|9|P113|
 +|19|Thermistor 1|V|TFE|24|Red|40|1|P113|
 +|20|Thermistor 1|W|TFE|24|Green|40|2|P113|
 +|21|+15V|X|TFE|22|Red|45|7|TB1|
 +|22|HT SUP. D/A (0 to +5V)|Y|   No Connection   ||||||
 +|23|HT SUPPLY 0V (GND 2)|Z|TFE|22|Black|80|13|P105|
 +</hidden>
 +<hidden ==== Card Rack- BA-W36 - P112 ====>
 +^Connector Number^Connector Part Number^
 +|**P112**|DAMA15S|
 +|TB1|Cinch 20-141|
 +|SW1|Push button|
 +
 +^Internal Destination^^Origination^^^^^External Destination^^
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^
 +|1|GND|1|TFE|22|Black|45|15|TB1|
 +|2|GND|2|TFE|22|Black|45|15|TB1|
 +| ||3|   No Connection   ||||||
 +| ||4|   No Connection   ||||||
 +| ||5|   No Connection   ||||||
 +| ||6|   No Connection   ||||||
 +| ||7|   No Connection   ||||||
 +|<del>7</del>|<del>Reset CLR</del>|<del>7</del>|<del>TFE</del>|<del>22</del>|<del>Grey</del>|<del>35</del>|<del>2</del>|<del>SW1</del>|
 +|8|-15V|8|TFE|22|Blue|40|11|TB1|
 +|9|+5V|9|TFE|22|Yellow|40|3|TB1|
 +| ||10|   No Connection   ||||||
 +|11|+15V|11|TFE|22|Red|35|6|TB1|
 +| ||12|   No Connection   ||||||
 +| ||13|   No Connection   ||||||
 +| ||14|   No Connection   ||||||
 +|15|+24V|15|TFE|22|Orange|10|40|TB1|
 +The reset switch (SW1) has been removed because it could be accidentally hit with the desiccant container
 +</hidden>
 +<hidden ==== Heatsink (External)- BA-W36 - P105 ====>
 +^Connector Number^Connector Part Number^
 +|**P105**|Cannon DBMA-25S|
 +|TB1|Cinch 20-141|
 +|P104|EDAC 322 044-500-258|
 +|P111|Cannon DEMA-9S|
 +
 +^Internal Destination^^Origination^^^^^External Destination^^
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^
 +|1|Shutter Motor +24V|1|TFE|22|Orange|55|8|TB1|
 +|2|Shutter Motor Feedback|2|TFE|22|Blue|80|A|P104|
 +|3|Shutter Motor Q303E|3|TFE|22|Green|85|C |P104|
 +|4|+15V  -  5V REG|4|TFE|22|Red|55|5|TB1|
 +|5|Std Lamp +15V|5|TFE|22|Red|50|4|TB1|
 +|6|Std Lamp +15V|6|TFE|22|Red|80|H|P104|
 +|7|Std Lamp Q103E / RCL|7|TFE|22|Violet|80|K|P104|
 +|8|0V HV REF RTN|8|TFE|22|Black|80|14|P104 (TP)|
 +|9|HG Lamp Q704B|9|TFE|22|Grey|80|1|P104|
 +|10|HG Lamp Q704E|10|TFE|22|Grey|80|3|P104|
 +|11|HG GTL3 Lamp |11|TFE|20|White|140|9|P111|
 +|12|HT Supply VE I/P  -12V|12|TFE|22|White|80|7|P104|
 +|13|HT Supply GND|13|TFE|22|Black|55|14|TB1|
 +|14|Shutter Motor Q303B|14|TFE|22|Green|80|D|P104|
 +|15|Shutter Motor Q303C|15|TFE|22|Green|80|F|P104|
 +|16||16| No Connection||||||
 +|17|+15V to R6 (~+10V)|17|TFE|22|White|80|11|P104|
 +|18|Std Lamp Q103B|18|TFE|22|Violet|80|L|P104|
 +|19|Std Lamp Q103C|19|TFE|22|Violet|80|M|P104|
 +|20|Std Lamp Source|20|TFE|20|Red|140|5|P111|
 +|21| HV CTRL I/P|21|TFE|22|Blue|80|15|P104 (TP)|
 +|22|+24V|22|TFE|22|Orange|55|9|TB1|
 +|23|HG Lamp Q704C  +24V|23|TFE|22|Orange|55|2|P104|
 +|24|HV +5V REF OUT|24|TFE|22|Yellow|80|17|P104|
 +|25|HT Supply Feedback|25|TFE|22|White|80|8|P104|
 +</hidden>
 +<hidden ==== HG & STD Lamp - BA-W36 - P111 ==== >
 +^Connector Number^Connector Part Number^
 +|TB1|Cinch 20-141|
 +|P105|Cannon DBMA-25S|
 +|P104|EDAC 322-044-500-258|
 +
 +^Internal Destination^^Origination^^^^^External Destination^^
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^
 +|1|STD LAMP GND|1|TFE|20|Black|110|17|TB1|
 +|2|N/C|2|   |   |   |   |N/C|   |
 +|3|N/C|2|   |   |   |   |N/C|   |
 +|4|N/C|2|   |   |   |   |N/C|   |
 +|5|STD Lamp V+|5|TFE|20|Red|150|20|P105|
 +|6|HG Lamp RTN|6|TFE|20|Green|110|4|P104|
 +|7|N/C|2|   |   |   |   |N/C|   |
 +|8|N/C|2|   |   |   |   |N/C|   |
 +|9|HG Lamp V+|9|TFE|20|White|150|11|P105|
 +</hidden>
 +<hidden ==== Power LED - BA-W36 ==== >
 +^Connector Number^Connector Part Number^
 +|TB1|Cinch 20-141|
 +
 +^Internal Destination^^Origination^^^^^External Destination^^
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^
 +|LED|GND|1|TFE|22|Black|110|18|TB1|
 +|LED|+5V|2|TFE|22|Yellow|100|3|TB1|
 +</hidden>
 +<hidden ==== Terminal Block - BA-W36 - TB1 ==== >
 +This is the Terminal block that is installed under the [[sps|Secondary Power Supply]]
 +^Connector Number^Connector Part Number^
 +|TB1|Cinch 20-141|
 +|P105|Cannon DBMA-25S|
 +|P104|EDAC 322-044-500-258|
 +|P2|Molex 0039012245|
 +|P105|Cannon DBMA-25S|
 +|LED|Molex 03-06-2011|
 +|P112|Cannon DAMA-15S|
 +|P104|EDAC 322-044-500-258|
 +|P111|Cannon DEMA-9S|
 +|R1|Ohmite 95J10R|
 +
 +^Internal Destination^^^Origination^^^^^External Destination^^
 +^Position^^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^
 +^+5V|2|Primary Power Supply|2|TFE|22|YEL|60|3|P2|
 +^:::|2|SPS Test Point +5V|2|TFE|22|YEL|30|5|TP5 +5V|
 +^:::|3|Primary Power Supply|3|TFE|22|YEL|61|15|P2|
 +^:::|3|+5V to Card Rack|3|TFE|22|YEL|34|9|P112|
 +^:::|3|Power Indicator|3|TFE|22|YEL|71|2|LED|
 +||||||||||
 +^+15V|4|Primary Power Supply|4|TFE|20|RED|58|1|P2|
 +^:::|4|+15V to SPS (TEMP)|4|TFE|22|RED|39|12|P104|
 +^:::|4|Wire Wrap 0.4 ohm |4|TFE|22|RED|51|5|P105|
 +^:::|5|R6 - 50 ohm 1% 5 W|5|TFE|22|RED|48|4|P105|
 +^:::|5|SPS Test Point +15V|5|TFE|22|RED|28|4|TP4 +15V|
 +^:::|6|+15V to Card Rack|6|TFE|22|RED|33|11|P112|
 +^:::|7|+15V to SPS (HT)|7|TFE|22|RED|42|X|P104|
 +||||||||||
 +^+24V|8|Primary Power Supply|8|TFE|22|ORG|61|8|P2|
 +^:::|8|R2 (1) - 3 ohm|8|TFE|22|ORG|50|1|P105|
 +^:::|9|+24V to SPS (HG)|9|TFE|22|ORG|41|2|P104|
 +^:::|9|HG Q704C / HV PWR|9|TFE|22|ORG|50|22|P105|
 +^:::|10|+24V to Card Rack|10|TFE|22|ORG|34|15|P112|
 +^:::|10|SPS Test Point +24V|10|TFE|22|ORG|25|7|TP7 +24V|
 +||||||||||
 +^-15V|11|R1(1)  -15V|11|TFE|22|BLU|91|1|R1|
 +^:::|11|-15V to Card Rack|11|TFE|22|BLU|36|8|P112|
 +^:::|12|-15V to SPS (REG/TEMP)|12|TFE|22|BLU|43|9|P104|
 +^:::|12|SPS Test Point -15V|12|TFE|22|BLU|28|6|TP6 -15V|
 +^13|13||13| No Connection|||||
 +^GND|14|Primary Power Supply|14|TFE|20|BLK|64|5|P2|
 +^:::|14|0V GND7 (HG)|14|TFE|22|BLK|48|5|P104|
 +^:::|14|0V GND2  (HT)|14|TFE|22|BLK|56|13|P105|
 +^:::|15|0V GND6 (TEMP)|15|TFE|22|BLK|46|16|P104|
 +^:::|15|0V GND4 (REG)|15|TFE|22|BLK|48|21|P104|
 +^:::|15|GND to Card Rack|15|TFE|22|BLK|41|1|P112|
 +^:::|16A|0V GND6 (TEMP3)|16A|TFE|22|BLK|48|T|P104|
 +^:::|16A|0V GND2 (HT)|16A|TFE|22|BLK|51|Z|P104|
 +^:::|16A|GND to Card Rack|16A|TFE|22|BLK|43|2|P112|
 +^:::|16B| |16B|TFE|20|BLK|69|11|+24V RTN|
 +^:::|16B|SPS Test Point GND|16B|TFE|22|BLK|38|1|TP1 GND|
 +^:::|17|Reset Switch|17|TFE|22|BLK|43|1|SW1|
 +^:::|17|0V GND1 (SL)|17|TFE|22|BLK|53|J|P104|
 +^:::|17|0V GND1 (SL)|17|TFE|22|BLK|53|J|PEN1|
 +^:::|17|STD LAMP GND|17|TFE|20|BLK|107|1|P111|
 +^:::|18|Primary Power Supply|18|TFE|20|BLK|69|17|P2|
 +^:::|18|Power Indicator GND|18|TFE|22|BLK|109|1|LED|
 +^:::|18|0V GND3 (MOTOR)|18|TFE|22|BLK|48|B|P104|
 +^:::|19|CASE GND|19|TFE|18|BLK|22|GND|HEATSINK BA-E21|
 +^:::|9|HG Lamp V+|9|TFE|20|White|150|11|P105|
 +</hidden>
 ====== FAQ ====== ====== FAQ ======
  
 **Q:** What are the differences between new vs old temperature circuit on the clock board?\\ **Q:** What are the differences between new vs old temperature circuit on the clock board?\\
-**A:** Note the resistors on the top left of the boards below (New Vs Old). New temperature circuits, some resistors has been replaced with a jumper wire.\\+**A:** Note the resistors on the top right of the boards below (New Vs Old). In the new temperature circuits, some resistors have been replaced with a jumper wire.\\
 {{:pictures:clock_board_old.vs.new.jpg?600|}}\\ {{:pictures:clock_board_old.vs.new.jpg?600|}}\\
  
-**Q:** How do I find out what what LED sensor is active?\\+**Q:** How do I find out what LED sensor is active?\\
 **A:** Depending on what you're looking for, you can use one of the 3 commands in MM <key>GET,800</key><key>GET,544</key><key>GET,1056</key>. This will yield the following **A:** Depending on what you're looking for, you can use one of the 3 commands in MM <key>GET,800</key><key>GET,544</key><key>GET,1056</key>. This will yield the following
 ^Bits^<key>GET,800</key>^<key>GET,544</key>^<key>GET,1056</key>^ ^Bits^<key>GET,800</key>^<key>GET,544</key>^<key>GET,1056</key>^
Line 82: Line 293:
 |6|Down Switch Pressed| | | |6|Down Switch Pressed| | |
 |7|Up Switch Pressed| | | |7|Up Switch Pressed| | |
-{{iframefs>http://cbsn.hiitravel.ca/scripts/bits.php 330px noscroll}}+{{iframefs>http://cbsn.hiitravel.ca:1080/scripts/bits.php 330px noscroll}}
  
multiboard.1743700234.txt.gz · Last modified: 2025/04/03 17:10 by reno