Canadian Brewer Spectrometer Network

User Tools

Site Tools

Trace:
multiboard

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
multiboard [2024/10/30 17:50] – renomultiboard [2025/11/27 11:59] (current) – [FAQ] reno
Line 1: Line 1:
 ====== Multiboard Electronics ====== ====== Multiboard Electronics ======
  
-The Multiboard electronics, sometimes referred to old electronics are usually used in the MKII and MKIV Brewers. Some of the earlier MKIII brewers may also be running the multiboard electronics.+The Multiboard electronics, sometimes referred to old electronics are usually used in the MKII and MKIV Brewers. Some of the earlier MKIII brewers may also be running the multiboard electronics. The multiboard electronics consist of the primary power supply¹ (PPS), [[sps|secondary power supply]], Card cage boards, and the heatsink.\\
  
 +¹Note, both multiboard and single board electronics both have an PPS, however the multiboard uses a 24V/15V/5V power supply while the single board electronics uses 24V/12V/5V power supply. The latest brewer's produced by Kip and Zonen (around Brewer # 250) uses the TDK-Lambda NV175 series power supply. The single Electronics board uses NV1-4G5TT, where the multiboard uses the NV14G5FF.
  
-====== FAQ ======+====== Card Cage ====== 
 +There are 7 cards that are needed for a brewer to be in operation. The following list is the order the boards are in from top to bottom. 
 +  - [[ioboard|IO Board (A)]] 
 +  - [[ioboard|IO Board (B)]] 
 +  - [[ioboard|IO Board (C)]] 
 +  - Microprocessor/RCA board 
 +  - Clock Board 
 +  - Analog to Digital Board 
 +  - [[photon_counter|Photon Counter Board]]
  
-**Q:** What are the differences between new vs old temperature circuit on the clock board?\\ +For Diagnostics purposes, the minimal amount of boards required to communicate to the brewer from a computer is just the Microprocessor/RCA board and the [[photon_counter|Photon Counter Board]]. All the other boards can be removed. This will help diagnose if there is a bad board causing communication issues.\\ 
-**A:** Note the resistors on the top left of the boards below (New Vs Old). New temperature circuits, some resistors has been replaced with a jumper wire.\\ +\\ 
-{{:pictures:clock_board_old.vs.new.jpg?600|}}\\+<hidden Cardcage Motherboard Signals> 
 +^Component side^^^^Solder Side^^^^ 
 +^Pin^Mnemonic^Signal Flow^Discription^Pin^Mnemonic^Signal Flow^Discription^ 
 +^A|TPA-P|Out|System Timing Pulse 1^1|DMAI-N|In|DMA Input Request| 
 +^B|TPD-P|Out|System Timing Pulse 2^2|DMAO-N|In|DMA Output Request| 
 +^C|DB0-P|In/Out|Data Bus^3|RNU-P|---|Run Utility| 
 +^D|DB1-P|In/Out|Data Bus^4|INT-P|In|Interrupt Request| 
 +^E|DB2-P|In/Out|Data Bus^5|MRD-N|Out|Memory Read| 
 +^F|DB3-P|In/Out|Data Bus^6|Q-P|Out|Programmed Output Latch| 
 +^H|DB4-P|In/Out|Data Bus^7|SCO0-P|Out|State Code| 
 +^J|DB5-P|In/Out|Data Bus^8|SCO1-P|Out|State Code| 
 +^K|DB6-P|In/Out|Data Bus^9|CLEAR-N|In|Clear-Mode Control| 
 +^L|DB7-P|In/Out|Data Bus^10|WAIT-N|In|Wait-Mode Control| 
 +^M|A0-P|Out|Multiplexed Address Bus^11|-5V/-15V|---|Auxiliary Power| 
 +^N|A1-P|Out|Multiplexed Address Bus^12|+24V|---|Auxiliary Power| 
 +^P|A2-P|Out|Multiplexed Address Bus^13|Clock Out|Out|Clock from CPU Osc.| 
 +^R|A3-P|Out|Multiplexed Address Bus^14|N0-P|Out|I/O Primary Address| 
 +^S|A4-P|Out|Multiplexed Address Bus^15|N1-P|Out|I/O Primary Address| 
 +^T|A5-P|Out|Multiplexed Address Bus^16|N2-P|Out|I/O Primary Address| 
 +^U|A6-P|Out|Multiplexed Address Bus^17|EF1-N|In|External Flag| 
 +^V|A7-P|Out|Multiplexed Address Bus^18|EF2-N|In|External Flag| 
 +^W|MWR-N|Out|Memory Write Pulse^19|EF3-N|In|External Flag| 
 +^X|EF4-N|In|External Flag^20|+12V/+15V|---|Auxiliary Power| 
 +^Y|+5V|In|+5VDc^21|+5V|In|+5 volts dc| 
 +^Z|GND|In|Digital Ground^22|GND|In|Digital Ground| 
 +</hidden> 
 +====== Wiring Harness ====== 
 +Note: These wiring harness are based on [[cbsn|CBSN]] brewer setup. Your brewer wiring may vary slightly 
 +<hidden ==== Secondary Power Supply - BA-W36 - P104 -TOP ====> 
 +^Connector Number^Connector Part Number^ 
 +|**P104**|EDAC 332-044-500-258| 
 +|TB1|Cinch 20-141| 
 +|P105|Cannon DBMA-25S| 
 +|P111|Cannon DEMA9S| 
 +|P113|Cannon DEMA9S| 
 +|PEN1|OST OSTVIN02A150|
  
-**Q:** What is the differences between new vs old temperature circuit on the SPS board?\\ +^Internal Destination^^Origination^^^^^External Destination^^ 
-**A:** Old circuit . Power Supply - **R601**, **R604** and **R605** are 11M and **R602**, **R606** and **R607** are 1.6M\\ +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
-New Sec. Power Supply - **R601**, **R604** and **R605** are 825K and  **R602**, **R606** and **R607** are 3M\\+|1|HG Lamp Q704B|1|TFE|22|Grey|80|9|P105| 
 +|2|HG Lamp Q704C/24V|2|TFE|22|Orange|45|9|TB1| 
 +|3|HG Lamp Q704E|3|TFE|22|Grey|80|10|P110| 
 +|4|Lamp RTN|4|TFE|20|Green|105|14|TB1| 
 +|5|GND|5|TFE|22|Black|50|14|TB1| 
 +|6|Output for Pen-ray HG Relay|6|TFE|20|Brown|80|3|PEN1| 
 +|7|HT Supply -VE In|7|TFE|22|White|80|12|P105| 
 +|8|HT Supply - Feedback|8|TFE|22|80|White|25|P105| 
 +|:::|SPS Test points HV|:::|TFE|22|White|15|3|TP3 HV| 
 +|9|-15V|9|TFE|22|Blue|45|12|TB1| 
 +|10|<del>SPS Test point RATE</del>|<del>10</del>|<del>TFE</del>|<del>22</del>|<del>Blue</del>|<del>13</del>|<del>8</del>|<del>TP8 Rate</del>| 
 +|11|~+10V|11|TFE|22|White|80|17|P105| 
 +|12|+15V|12|TFE|22|Red|40|5|TB1| 
 +|13|Thermistor output 2|   Onboard Connector   |||||2|J101| 
 +|14|HV Ref Return|14|TFE|22|Black|80|8|P105| 
 +|15|HV CTRL IN|15|TFE|22|Blue|80|21|P105| 
 +|16|Temp 0 V (Ground 6)|16|TFE|22|Black|50|15|TB1| 
 +|17|HV+5V REF Out|17|TFE|22|Yellow|80|24|P105| 
 +|18|Thermistor output 3|   Onboard Connector   |||||1|J101| 
 +|19|SPS Testpoints TEMP|19|TFE|22|Red|15|2|TP2 Temp| 
 +|:::|Thermistor output 1|   Onboard Connector   |||||3|J101| 
 +|20|Thermistor 1|20|TFE|24|Brown|40|3|P113| 
 +|21|GND|21|TFE|22|Black|40|3|P113| 
 +|22|HT Supply -12V|22|TFE|22|Violet|100|2|R1| 
 +|:::|SPS Testpoints -12V|:::|TFE|22|Violet|20|9|TP9-12V| 
 +**Notes:**\\ 
 +**HT** - Refers to the original high voltage module (Centronics PS 336-10-2000-ND+F DC-DC PS) that is mounted to the Heatsink.\\ 
 +**HV** - Refers to the new high voltage module (Ultravolt - 2AA24-P20-M) that is mounted to the heatsink\\ 
 +**TP#xx** - Refers to the test point bracket 
 +**Pen-ray Relay** - Refers to the external Pen-ray HG controller. This replaces the traditional mercury filament bulb with a pen-ray style mercury lamp.\\ 
 +**Rate Meter  (Pin 10)** - Rate test points has been grounded off on the old [[sps|SPS]] and left unused on the new [[sps|SPS]].\\ 
 +Pin 6, 14, 15 and 17 previously has no connection on the old [[sps|SPS]]\\
  
-**Q:** What pot controls what on the SPS board?\\ +</hidden> 
-**A:** {{:pictures:sps_pots.png?400|}}+<hidden ==== Secondary Power Supply - BA-W36 - P104 -Bottom ==== 
 +> 
 +^Connector Number^Connector Part Number^ 
 +|**P104**|EDAC 332-044-500-258| 
 +|TB1|Cinch 20-141| 
 +|P105|Cannon DBMA-25S| 
 +|P111|Cannon DEMA9S| 
 +|P113|Cannon DEMA9S|
  
-**Q:** What are the jumper settings for multi IO board (IOS) ____?\\ +^Internal Destination^^Origination^^^^^External Destination^^ 
-**A:**  +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
-^Part#^J6^J7^J8^J9^J10^J11^J12^J13^J14^J15^J16^ +|1|Shutter +24V / RCL|A|TFE|22|Blue|80|2|P105| 
-|BA-E50/A|1-2|NC|2-3|2-3|2-3|1-2|1-2|1-2|1-2|2-3|N2| +|2|Shutter 0V (GND 3)|B|TFE|22|Black|60|18|TB1| 
-|BA-E50/B|2-3|2-3|1-2|1-2|1-2|1-2|1-2|1-2|1-2|2-3|N4| +|3|Shutter RCL / Q303E|C|TFE|22|Green|80|3|P105| 
-|BA-E50/D|2-3|2-3|1-2|1-2|1-2|1-2|2-3|2-3|2-3|2-3|N3| +|4|Shutter RCL / Q303B|D|TFE|22|Green|80|14|P105| 
-|BA-E50/E|1-2|2-3|1-2|1-2|1-2|1-2|2-3|2-3|2-3|2-3|N3|+|5| |E|   No Connection   |||||| 
 +|6|Shutter Motor / Q303C|F|TFE|22|Green|80|15|P105| 
 +|7|Std Lamp   +15V/RCL|H|TFE|22|Red|80|6|P105| 
 +|8|Std Lamp  0V  (GND 1)|J|TFE|22|Black|55|17|TB1| 
 +|9|Std Lamp  Q103E/RCL|K|TFE|22|Violet|80|7|P105| 
 +|10|Std Lamp  Q103B|L|TFE|22|Violet|79|20|P105| 
 +|11|Std Lamp  Q103B|M|TFE|22|Violet|79|20|P105| 
 +|12|Thermistor 2|N|TFE|24|Red|40|4|P113| 
 +|13|Thermistor 2|P|TFE|24|Green|40|5|P113| 
 +|14|Thermistor 2|R|TFE|24|Brown|40|6|P113| 
 +|15|Thermistor 3|S|TFE|24|Red|40|7|P113| 
 +|16|Thermistor 3|T|TFE|24|Green|40|8|P113| 
 +|17|(GND 6)|T|TFE|22|Black|55|16|TB1| 
 +|18|Thermistor 3|U|TFE|24|Brown|40|9|P113| 
 +|19|Thermistor 1|V|TFE|24|Red|40|1|P113| 
 +|20|Thermistor 1|W|TFE|24|Green|40|2|P113| 
 +|21|+15V|X|TFE|22|Red|45|7|TB1| 
 +|22|HT SUP. D/A (0 to +5V)|Y|   No Connection   |||||| 
 +|23|HT SUPPLY 0V (GND 2)|Z|TFE|22|Black|80|13|P105| 
 +</hidden> 
 +<hidden ==== Card Rack- BA-W36 - P112 ====> 
 +^Connector Number^Connector Part Number^ 
 +|**P112**|DAMA15S| 
 +|TB1|Cinch 20-141| 
 +|SW1|Push button|
  
-**Q:** What control goes to what connector?\\ +^Internal Destination^^Origination^^^^^External Destination^^ 
-**A:** +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
-^Part#^J1^J2^J3^J4^J5^Applies^ +|1|GND|1|TFE|22|Black|45|15|TB1| 
-|BA-E50/A|NC|Micrometer|Shutter|SPS|NC|MkII & MkIV| +|2|GND|2|TFE|22|Black|45|15|TB1| 
-|BA-E50/B|Iris|FW#1|FW#2|NC|NC|MkII, MkIII & MkIV| +| ||3|   No Connection   |||||| 
-|BA-E50/D|Zenith|Azimuth|FW#3|Control|NC|MkIV| +| ||4|   No Connection   |||||| 
-|Ba-E50/E|Zenith|Azimuth|Micrometer#2|Control|NC|MkIII| +| ||5|   No Connection   |||||| 
-|SPS|A2D|BA-E50/A|Heat Sink| | | +| ||6|   No Connection   |||||| 
-\\ +| ||7|   No Connection   |||||| 
-**Q:** How do I find out what what LED sensor is active?\\+|<del>7</del>|<del>Reset CLR</del>|<del>7</del>|<del>TFE</del>|<del>22</del>|<del>Grey</del>|<del>35</del>|<del>2</del>|<del>SW1</del>| 
 +|8|-15V|8|TFE|22|Blue|40|11|TB1| 
 +|9|+5V|9|TFE|22|Yellow|40|3|TB1| 
 +| ||10|   No Connection   |||||| 
 +|11|+15V|11|TFE|22|Red|35|6|TB1| 
 +| ||12|   No Connection   |||||| 
 +| ||13|   No Connection   |||||| 
 +| ||14|   No Connection   |||||| 
 +|15|+24V|15|TFE|22|Orange|10|40|TB1| 
 +The reset switch (SW1) has been removed because it could be accidentally hit with the desiccant container 
 +</hidden> 
 +<hidden ==== Heatsink (External)- BA-W36 - P105 ====> 
 +^Connector Number^Connector Part Number^ 
 +|**P105**|Cannon DBMA-25S| 
 +|TB1|Cinch 20-141| 
 +|P104|EDAC 322 044-500-258| 
 +|P111|Cannon DEMA-9S| 
 + 
 +^Internal Destination^^Origination^^^^^External Destination^^ 
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
 +|1|Shutter Motor +24V|1|TFE|22|Orange|55|8|TB1| 
 +|2|Shutter Motor Feedback|2|TFE|22|Blue|80|A|P104| 
 +|3|Shutter Motor Q303E|3|TFE|22|Green|85|C |P104| 
 +|4|+15V  -  5V REG|4|TFE|22|Red|55|5|TB1| 
 +|5|Std Lamp +15V|5|TFE|22|Red|50|4|TB1| 
 +|6|Std Lamp +15V|6|TFE|22|Red|80|H|P104| 
 +|7|Std Lamp Q103E / RCL|7|TFE|22|Violet|80|K|P104| 
 +|8|0V HV REF RTN|8|TFE|22|Black|80|14|P104 (TP)| 
 +|9|HG Lamp Q704B|9|TFE|22|Grey|80|1|P104| 
 +|10|HG Lamp Q704E|10|TFE|22|Grey|80|3|P104| 
 +|11|HG GTL3 Lamp |11|TFE|20|White|140|9|P111| 
 +|12|HT Supply VE I/P  -12V|12|TFE|22|White|80|7|P104| 
 +|13|HT Supply GND|13|TFE|22|Black|55|14|TB1| 
 +|14|Shutter Motor Q303B|14|TFE|22|Green|80|D|P104| 
 +|15|Shutter Motor Q303C|15|TFE|22|Green|80|F|P104| 
 +|16||16| No Connection|||||| 
 +|17|+15V to R6 (~+10V)|17|TFE|22|White|80|11|P104| 
 +|18|Std Lamp Q103B|18|TFE|22|Violet|80|L|P104| 
 +|19|Std Lamp Q103C|19|TFE|22|Violet|80|M|P104| 
 +|20|Std Lamp Source|20|TFE|20|Red|140|5|P111| 
 +|21| HV CTRL I/P|21|TFE|22|Blue|80|15|P104 (TP)| 
 +|22|+24V|22|TFE|22|Orange|55|9|TB1| 
 +|23|HG Lamp Q704C  +24V|23|TFE|22|Orange|55|2|P104| 
 +|24|HV +5V REF OUT|24|TFE|22|Yellow|80|17|P104| 
 +|25|HT Supply Feedback|25|TFE|22|White|80|8|P104| 
 +</hidden> 
 +<hidden ==== HG & STD Lamp - BA-W36 - P111 ==== > 
 +^Connector Number^Connector Part Number^ 
 +|TB1|Cinch 20-141| 
 +|P105|Cannon DBMA-25S| 
 +|P104|EDAC 322-044-500-258| 
 + 
 +^Internal Destination^^Origination^^^^^External Destination^^ 
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
 +|1|STD LAMP GND|1|TFE|20|Black|110|17|TB1| 
 +|2|N/C|2|   |   |   |   |N/C|   | 
 +|3|N/C|2|   |   |   |   |N/C|   | 
 +|4|N/C|2|   |   |   |   |N/C|   | 
 +|5|STD Lamp V+|5|TFE|20|Red|150|20|P105| 
 +|6|HG Lamp RTN|6|TFE|20|Green|110|4|P104| 
 +|7|N/C|2|   |   |   |   |N/C|   | 
 +|8|N/C|2|   |   |   |   |N/C|   | 
 +|9|HG Lamp V+|9|TFE|20|White|150|11|P105| 
 +</hidden> 
 +<hidden ==== Power LED - BA-W36 ==== > 
 +^Connector Number^Connector Part Number^ 
 +|TB1|Cinch 20-141| 
 + 
 +^Internal Destination^^Origination^^^^^External Destination^^ 
 +^Position^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
 +|LED|GND|1|TFE|22|Black|110|18|TB1| 
 +|LED|+5V|2|TFE|22|Yellow|100|3|TB1| 
 +</hidden> 
 +<hidden ==== Terminal Block - BA-W36 - TB1 ==== > 
 +This is the Terminal block that is installed under the [[sps|Secondary Power Supply]] 
 +^Connector Number^Connector Part Number^ 
 +|TB1|Cinch 20-141| 
 +|P105|Cannon DBMA-25S| 
 +|P104|EDAC 322-044-500-258| 
 +|P2|Molex 0039012245| 
 +|P105|Cannon DBMA-25S| 
 +|LED|Molex 03-06-2011| 
 +|P112|Cannon DAMA-15S| 
 +|P104|EDAC 322-044-500-258| 
 +|P111|Cannon DEMA-9S| 
 +|R1|Ohmite 95J10R| 
 + 
 +^Internal Destination^^^Origination^^^^^External Destination^^ 
 +^Position^^Function^Pin^Wire Type^Gauge^Colour^Length(CM)^PIN^Connector^ 
 +^+5V|2|Primary Power Supply|2|TFE|22|YEL|60|3|P2| 
 +^:::|2|SPS Test Point +5V|2|TFE|22|YEL|30|5|TP5 +5V| 
 +^:::|3|Primary Power Supply|3|TFE|22|YEL|61|15|P2| 
 +^:::|3|+5V to Card Rack|3|TFE|22|YEL|34|9|P112| 
 +^:::|3|Power Indicator|3|TFE|22|YEL|71|2|LED| 
 +|||||||||| 
 +^+15V|4|Primary Power Supply|4|TFE|20|RED|58|1|P2| 
 +^:::|4|+15V to SPS (TEMP)|4|TFE|22|RED|39|12|P104| 
 +^:::|4|Wire Wrap 0.4 ohm |4|TFE|22|RED|51|5|P105| 
 +^:::|5|R6 - 50 ohm 1% 5 W|5|TFE|22|RED|48|4|P105| 
 +^:::|5|SPS Test Point +15V|5|TFE|22|RED|28|4|TP4 +15V| 
 +^:::|6|+15V to Card Rack|6|TFE|22|RED|33|11|P112| 
 +^:::|7|+15V to SPS (HT)|7|TFE|22|RED|42|X|P104| 
 +|||||||||| 
 +^+24V|8|Primary Power Supply|8|TFE|22|ORG|61|8|P2| 
 +^:::|8|R2 (1) - 3 ohm|8|TFE|22|ORG|50|1|P105| 
 +^:::|9|+24V to SPS (HG)|9|TFE|22|ORG|41|2|P104| 
 +^:::|9|HG Q704C / HV PWR|9|TFE|22|ORG|50|22|P105| 
 +^:::|10|+24V to Card Rack|10|TFE|22|ORG|34|15|P112| 
 +^:::|10|SPS Test Point +24V|10|TFE|22|ORG|25|7|TP7 +24V| 
 +|||||||||| 
 +^-15V|11|R1(1)  -15V|11|TFE|22|BLU|91|1|R1| 
 +^:::|11|-15V to Card Rack|11|TFE|22|BLU|36|8|P112| 
 +^:::|12|-15V to SPS (REG/TEMP)|12|TFE|22|BLU|43|9|P104| 
 +^:::|12|SPS Test Point -15V|12|TFE|22|BLU|28|6|TP6 -15V| 
 +^13|13||13| No Connection||||| 
 +^GND|14|Primary Power Supply|14|TFE|20|BLK|64|5|P2| 
 +^:::|14|0V GND7 (HG)|14|TFE|22|BLK|48|5|P104| 
 +^:::|14|0V GND2  (HT)|14|TFE|22|BLK|56|13|P105| 
 +^:::|15|0V GND6 (TEMP)|15|TFE|22|BLK|46|16|P104| 
 +^:::|15|0V GND4 (REG)|15|TFE|22|BLK|48|21|P104| 
 +^:::|15|GND to Card Rack|15|TFE|22|BLK|41|1|P112| 
 +^:::|16A|0V GND6 (TEMP3)|16A|TFE|22|BLK|48|T|P104| 
 +^:::|16A|0V GND2 (HT)|16A|TFE|22|BLK|51|Z|P104| 
 +^:::|16A|GND to Card Rack|16A|TFE|22|BLK|43|2|P112| 
 +^:::|16B| |16B|TFE|20|BLK|69|11|+24V RTN| 
 +^:::|16B|SPS Test Point GND|16B|TFE|22|BLK|38|1|TP1 GND| 
 +^:::|17|Reset Switch|17|TFE|22|BLK|43|1|SW1| 
 +^:::|17|0V GND1 (SL)|17|TFE|22|BLK|53|J|P104| 
 +^:::|17|0V GND1 (SL)|17|TFE|22|BLK|53|J|PEN1| 
 +^:::|17|STD LAMP GND|17|TFE|20|BLK|107|1|P111| 
 +^:::|18|Primary Power Supply|18|TFE|20|BLK|69|17|P2| 
 +^:::|18|Power Indicator GND|18|TFE|22|BLK|109|1|LED| 
 +^:::|18|0V GND3 (MOTOR)|18|TFE|22|BLK|48|B|P104| 
 +^:::|19|CASE GND|19|TFE|18|BLK|22|GND|HEATSINK BA-E21| 
 +^:::|9|HG Lamp V+|9|TFE|20|White|150|11|P105| 
 +</hidden> 
 +====== FAQ ====== 
 + 
 +**Q:** What are the differences between new vs old temperature circuit on the clock board?\\ 
 +**A:** Note the resistors on the top right of the boards below (New Vs Old). In the new temperature circuits, some resistors have been replaced with a jumper wire.\\ 
 +{{:pictures:clock_board_old.vs.new.jpg?600|}}\\ 
 + 
 +**Q:** How do I find out what LED sensor is active?\\
 **A:** Depending on what you're looking for, you can use one of the 3 commands in MM <key>GET,800</key><key>GET,544</key><key>GET,1056</key>. This will yield the following **A:** Depending on what you're looking for, you can use one of the 3 commands in MM <key>GET,800</key><key>GET,544</key><key>GET,1056</key>. This will yield the following
 ^Bits^<key>GET,800</key>^<key>GET,544</key>^<key>GET,1056</key>^ ^Bits^<key>GET,800</key>^<key>GET,544</key>^<key>GET,1056</key>^
 |0|CW Switch Pressed|Slitmask @ 7| | |0|CW Switch Pressed|Slitmask @ 7| |
 |1|CCW Switch Pressed|Slitmask @ 0| | |1|CCW Switch Pressed|Slitmask @ 0| |
-|2|CW AZ Sensor Blocked|Mic1 @ Max WL| | +|2|CW AZ Sensor Blocked|Mic1 @ Max WL(Mirror side)| | 
-|3|CCW AZ Sensor Blocked|Mic1 @ min WL| |+|3|CCW AZ Sensor Blocked|Mic1 @ min WL(Bulkhead side)| |
 |4|ZE Sensor Blocked| |Iris Fully open| |4|ZE Sensor Blocked| |Iris Fully open|
 |5|FW3 Sensor Blocked(Mic2 @ Max wl in MKIII)|FW3 Sensor Blocked in MKIII|Iris Fully Open| |5|FW3 Sensor Blocked(Mic2 @ Max wl in MKIII)|FW3 Sensor Blocked in MKIII|Iris Fully Open|
 |6|Down Switch Pressed| | | |6|Down Switch Pressed| | |
 |7|Up Switch Pressed| | | |7|Up Switch Pressed| | |
-{{iframefs>http://cbsn.hiitravel.ca/scripts/bits.php 330px noscroll}}+{{iframefs>http://cbsn.hiitravel.ca:1080/scripts/bits.php 330px noscroll}}
  
multiboard.1730310656.txt.gz · Last modified: 2024/10/30 17:50 by reno