Differences

This shows you the differences between two versions of the page.

--- documents [2021/12/16 14:39] – mbrohart
+++ documents [2024/09/11 17:28] (current) – andrew
@@ Line 2: / Line 2: @@
 ===== SOP =====
 {{ :docs:brewer_site_operators_manual_v2.2.pdf |Brewer Site Operators SOP}}\\
-{{ :docs:aersol_optical_depth_sop_v2.pdf|Aersol Optical Depth}}\\
+{{ :docs:aersol_optical_depth_sop_v2.pdf|Aerosol Optical Depth}}\\
 {{ :docs:sun_scan_sop_v2.pdf |Sun Scan}}\\
 {{ :docs:dispersion_calibration_sop_2020_v2.1.pdf |Dispersion Calibration}}\\
@@ Line 8: / Line 8: @@
 {{ :docs:zs_coeff_generation_sop_v2.pdf |ZS Coeff Generation}}\\
 {{ :docs:ozone_cal_sop_final.pdf |Ozone Cal}}\\
-{{ :docs:brewer_temp_coeff_generation_sop.pdf |Temp Cal}}
+{{ :docs:brewer_temp_coeff_generation_sop.pdf |Temp Cal}}\\
+[[http://cbsn.ca/dokuwiki/doku.php?id=zsf|Zenith Sky Chart Coefficient Generation SOP]]
 ===== Manuals =====
+{{ :docs:brewer_mkii_operators_manual.pdf |Brewer MKII Operators Manual}}\\
 {{ :docs:brewer_mkiii_operators_manual_revd.pdf |Brewer MKIII Operators Manual}}\\
 {{ :docs:mkiii_service_manual_revd_sb.pdf |Brewer MKIII Service Manual}}\\
@@ Line 19: / Line 21: @@
 {{ :docs:basic_maintenance.pdf | Basic Maintenance}}
 ===== Standard Work Procedures =====
-{{ :docs:data_cable_wiring.pdf | Data Cable Wiring}}\\
+{{ :docs:brewer_spectrometer_shipping_instructions_v2.pdf | Brewer Spectrometer Shipping Instructions}}\\
 {{ :docs:tracker_upgrade_refurbishment.pdf | Tracker Rotary Connector Upgrade & Refurbishment}}\\
+{{ :docs:firmware_config_upload.pdf | Brewer Firmware and Configuration Update Procedures}}\\
+{{ :docs:no2_micro_offset_value.pdf | NO2 Micrometer Setup}}\\
+{{ :docs:finding_micrometer.pdf | Initial Determination of the Micrometer Reference}}\\
+{{ :docs:finding_a_dispersion_from_scratch.pdf | Manual Dispersion Calculation of a Brewer}}\\
+===== Other Useful Pages =====
+[[linux|Linux - Additional Tricks and Tips]]\\
+[[software_setup|Setting up a Brewer on a New Computer & Setting up a new brewer on a computer]]\\
+[[creator.py|Creator Script information]]\\
+[[firmware|MKIII Brewer Firmware Update instructions]]
 ===== Historic Information =====
-{{ :docs:micrometer_optical_led_reference_triggering.pdf | Brewer Micrometer Optical LED Triggering
+{{ :docs:micrometer_optical_led_reference_triggering.pdf | Brewer Micrometer Optical LED Triggering}}\\
 {{ :docs:tracker_wire_diagram.pdf | Tracker Wire Diagram}}\\
 {{ :docs:brewer_calculation_rh_temp.pdf | Brewer Calculation of RH and Temp}}\\
+{{ :docs:modifying_the_zero_position.pdf | Modifying the zero position of a Brewer}}\\
 {{ :docs:nv175_pinouts.pdf | TDK Lambda NV175 Pinouts}}\\
 {{ :docs:nv175_sb.pdf | TDK Lambda NV175 Single board config}}\\
@@ Line 31: / Line 43: @@
 {{ :docs:ios_microboard_jumpers.pdf | IOS Microprocessor Board Jumper Settings}}\\
 {{ :docs:ios_multi_io_board.pdf | IOS Multi Configuration I/O Board Jumper Table}}\\
-{{ :docs:firmware_config_upload.pdf | Brewer Firmware and Configuration Update Procedures}}\\
+{{ :docs:data_cable_wiring.pdf | Data Cable Wiring}}\\
-{{ :docs:no2_micro_offset_value.pdf | NO2 Micrometer Setup}}\\
+{{ :docs:shutter_cct_setup_multiboard_elec.pdf | Shutter Motor Setup}}\\